Injen is proud to be introducing the all new Evolution sealed cold air intake system for the 2015-2018 BMW M3/M4! This intake has been designed using the some of the most up-to-date engineering tools and techniques to produce a top notch kit. This intake system is on a whole new level with one-piece sealed housings that utilize the all new Injen Twist-lock System (Patent Pending) to securely attach the Injen SuperNano-Web Dry air filters in place. This cold air intake also has our distinctive sight window that not only allows easy inspection of the air filters, but it really pops under your hood too. This kit ships complete with premium hardware to provide you the absolute best intake kit available for your BMW M3 and M4.
Both of the one-piece sealed housings utilize the all new Injen Twist-lock System (Patent Pending) to securely attach the SuperNano-Web Dry air filter in place which eliminates the use of unnecessary hardware and provides a simple installation that anyone can accomplish. To top it all off, the housings sport our all new ClearVue badge for easy filter inspection and also provides a clean look that pops every time you open the hood.
Roto-molded Intake Tubes:
This Evolution Air Intake System uses a couple of custom designed and dyno-tuned, intake tubes to produces huge power gains while retaining a clean and quality fit.
SuperNano-Web Dry Air Filters:
The SuperNano-Web Dry air filter is uniquely designed to work with the Injen Technology Twist-Lock System (Patent Pending). The Twist-Lock system has allowed our engineers to use one of the largest filters possible to increases air volume while keeping the installation process simple.
Stainless Steel Band Clamps with inner protective liner and reinforced automotive grade silicone couplers are used to provide the most secure installation available.
Created and designed 100% in 3D, our Evolution cold air intakes fit on a level equal to or above the OE system. Clean lines that flow with the entire engine compartment really set this intake apart from the competition. This Evolution cold air intake system also utilizes our all-new Twist-Lock System (Patent Pending) to provide the end user with one of the quickest and simplest installations available today.
After hours of design and dyno testing, This Evolution Air Intake system was putting down 22 additional horsepower and 27 lbs. of torque. Thats power that youll instantly feel.
Direct Fit for
2015-2020 BMW M4 (F82/83) L6-3.0L (tt)
2015-2018 BMW M3 (F80) L6-3.0L (tt)
2019-2020 BMW M2 Competition (F87) L6-3.0L (tt)
Dyno Proven gains of up to 22 hp and 27 lb-ft. of torque
Designed to work with the stock calibration
Aggressive intake growl under acceleration
Durable Roto-Molded Polyethylene tubes and housings
Twist-Lock Technology* to securely integrate the air filter to the housing
Reinforced automotive grade silicone couplers
Fully serviceable Injen SuperNano-Web dry air filter
Replacement air filter # X-1097-BB
Stainless steel band clamps with inner protective liner
Aggressive under hood appearance while maintaining an OE fit
Our clear inspection badge allows you to quickly check the condition of your air filter while the red stripe enhances under hood appearances.
Made in Pomona California, USA
Injen Technology Limited Lifetime Warranty
This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.
Prop 65 Compliance
This product can expose you to chemicals including Chromium, Nickel, Carbon Black & Cobalt, which are known to the State of California to cause cancer.
Injen Technology offers a Limited Lifetime Warranty to the original purchaser against defects in material and workmanship on all intake systems, air filters, and hydroshields. Injen Technology will replace, at no charge, any intake pipe, air filter, or hydroshield considered by Injen Technology to be defective. Any and all warranty coverage is limited to the repair or replacement of the defective part only, at Injen Technology’s discretion. Proof of purchase is required. The warranty does not cover incidental or consequential damages, damages caused from improper installation, nor does it cover the cost of installation or removal of the defective part or its replacement. All warranty items must be sent freight prepaid with a valid RMA (Return Merchandise Authorization) number and copy of original invoice.